DBA 201 F200 (8) mm (in.) | 440 W | 0.4 Ohm | Super Flat Sealed

High performance in a super flat design

The DBA 201 F flat active subwoofer enclosure optimized with FEM simulation ensures superior performance, maximizing the subwoofer output with a super flat size. The massive magnet of the 8 in. driver provides optimal control during the highest cone excursion.

Extra full set of controls to fine-tune the in-car performance
The built-in 24 dB/Oct. low-pass crossover filter with a variable cutting corner frequency (50÷150 Hz) allows you to perfectly match the DBA 201 F to your speaker system. Adjustable bass boost (0÷6 dB @ 45Hz) can add bass output as you prefer, allowing correction for OEM sound equalization. With the phase inverter (0-180°), you can optimize phase alignment between the DBA 201 F and your speaker system, regardless of the subwoofer’s position in the car. The subsonic filter (15 Hz @ 24 dB/Oct) protects the cone from over-excursion and amplifiers from overheating. The input sensitivity control is the perfect tool to maximize the overall system output level while preventing clipping.

Auto turn-on and standby mode
The built-in audio sense circuit allows the DBA 201 F to turn on and timeout to standby mode automatically. You can switch off the audio sense function when a remote turn-on wire is available.

Technical Specs

Size mm (in.)	200 (8)
Power Handling - Continuous W	220
Power Handling - Peak W	440
Impedance Ohm	0.4
Design	Super Flat Sealed
Voice Coil Ø	38.6 (1.52) mm (in.)
Frequency Response Hz	32 ÷ 400
Magnet size D x d x h mm (in.)	110 x 45 x 17 (4.33 x 1.78 x 0.67)
Weight of one component kg (lb.)	4.3 (9.48)
Magnet	High Density Flux Ferrite
Cone	Pressed paper
Voice Coil Type	Copper

Power Supply

Operating voltage VDC (Fuse)	6.5 ÷ 18 (15A)
Start - Stop voltage VDC	6
Idling current A (Power OFF)	260 m (1 m)
Consumption @ 14,4 VDC Max musical power A	8.5
Remote IN Turn on VDC (Current)	4 (1 mA)
PRE input signal Turn ON VRMS	10 mV
SPK input DC Turn ON VDC	2

Amplifier Stage

Distortion - THD @ 100 Hz %	0.15
Bandwidth Hz	15 - 150
S/N ratio dBA	100
Output power (RMS) @ 14,4 VDC, 1% THD W	220

Signals Inputs / Filter

PRE input signal VRMS (impedance)	0.2 ÷ 5 (10kΩ)
SPK input signal VRMS (impedance)	1.2 ÷ 30 (6Ω)
LO-PASS Filter @ 24 dB Oct adjustable Hz	50 ÷ 150
Subsonic Filter @ 24 dB Oct Fixed Hz	15
Phase switch	0 / 180°
Bass Boost @45 Hz dB	0 ÷ 6
Sub remote volume control dB	0 ÷ -15 (HRC 01 included)

Physical Specs

mm	in
A	345	13.58
B	245	9.64
C	79	3.11

Distortion - THD @ 100 Hz %	0.15
Bandwidth Hz	15 - 150
S/N ratio dBA	100
Output power (RMS) @ 14,4 VDC, 1% THD W	220

HERTZ

HERTZ DBA 201 F